How To Turn Off Water Supply To Samsung Refrigerator

If your dwelling house doesn't have a water line installed from a previous refrigerator, you will demand a water line that can run betwixt the water pipes in your home and your refrigerator.Water lines are typically sold in kits and are not included with the refrigerator. We recommend using a h2o line installation kit that uses 1/4 inch copper tubing, a 1/4 inch compression nut, and a ferrule. Keep in listen that you volition demand a pinch nut at both ends, and some kits only come with i.

This procedure will vary depending on the type of equipment you are using, so follow the kit's instructions. You tin besides employ our instructional video and steps if y'all're unsure.

In almost installations, the fundamentals include attaching a shut off valve (C) to your cold water line (A) using a piping clamp (B). Please refer to the first epitome for this step.
Then, yous'll need to twist the valve until it pierces your water line.
Subsequently that, you'll need to connect the remainder of the water line installation kit (D) to the close off valve (C). Please refer to the second image for this footstep.

Note: For the water ice maker to operate properly, a minimum water pressure level of 30 psi is required. If needed, you can install a booster pump to compensate for low pressure. After installation, check the water pressure by dispensing water. It should take less than 10 seconds to dispense three/iv cup.

Illustration of a shut off valve connected to a cold water line using a pipe clamp

Illustration of a water line installation kit being connected to the shut off valve

Note: The RS27T and RS22T models have two h2o lines to connect, which is not shown here. If they are cross-connected, the water and ice dispensing functions volition not piece of work correctly. If yous have ane of these models and the dispenser has non worked since installation, refer to the user manual to check that these lines are correctly installed.

The water supply line is non included with the refrigerator and is typically sold every bit a kit at your local hardware store (if you don't have one already installed in your home). Nosotros recommend getting a 1/4 inch copper tubing kit, which should include 1/four inch copper tubing, a 1/4 inch compression nut, and a ferrule.

A plastic tubing kit should include i/4 inch plastic tubing with a molded end/seedling, and a one/4 inch compression nut. If you use plastic tubing, do not use information technology without the molded cease/bulb. Please annotation that a plastic tubing kit is not recommended.

Please refer to the paradigm to see what the connectedness will look like using either type of tubing. This image is likewise available in your user manual. The ferrule for copper tubing, the molded end/bulb for plastic tubing, and the ane/4 inch compression nut for both tubing options volition be provided in the purchased kit.

(01): 1/four inch pinch nut
(02): Ferrule for copper tubing
(04): Plastic tubing leading to the refrigerator
(05): Pinch fitting
(06): Molded stop/bulb for plastic tubing
(07): 1/four inch compression nut for both tubing options

Illustration showing what the water line installation looks like using either copper or plastic tubing

(A): Section that leads to the refrigerator
(B): Section that leads to the household water supply line
(C): Demonstrates how the tubing will appear when installed

Utilise the instructions below to connect the h2o supply line:

Slip the compression nut (07) onto the tubing provided in the kit. If you are using copper tubing, also skid on the ferrule (02). If you lot are using plastic tubing, insert the molded end/seedling (06) straight into the compression fitting (05).
Tighten the pinch nut (07) until it reaches the compression plumbing equipment (05). Practice non over-tighten information technology, as over-tightening will cause a leak.
Plow the h2o on and check for leaks. If y'all find h2o drops or a leak in the connection areas, turn off the chief water supply. Bank check the connections, and tighten when necessary.
If the model has a dispenser, make sure the water filter is installed. Then, manipulate one gallon of water before drinking or using any water from the refrigerator.
The get-go fourth dimension y'all turn on the ice maker, let it make ice for 1 to 2 days. Over that period of time, throw out the first 2 buckets of ice to ensure all impurities have been removed from the water line.